Router settings D-Link DIR-300

Options DIR-300 NRU B6

CONTENT

  • 1 Varieties router D-Link DIR-300 and their characteristics
  • 2 How to connect the router D-Link DIR-300
  • 3 How do I reset the router D-Link DIR-300
  • 4 How to configure a router D-Link DIR-300
  • 5 What to do if you want the router firmware
  • 6 Features a router settings D-Link DIR-300 as an example Beeline provider
  • 7 Features settings of the router D-Link DIR-300 as an example a provider Rostelecom
  • 8 Prices for routers DIR-300, commercially available

Varieties router D-Link DIR-300 and their characteristics

The model is really quite good, and at the time she liked a lot. Perhaps, therefore, later it was released a few modifications, or, as we say, audit. Let's look at each in more detail.

DIR-300 A1

The first router, which was issued in 2007. It marked the beginning of the series. 1 was equipped with an external antenna, 1 WAN-port and 4 LAN. As the processor Atheros AR2317 was used with a frequency of 182 MHz. RAM on it was 16 MB and memory for data storage - 4MB.

One of the first router was very simple

DIR-300 B1, B2, B3, B4

Produced since 2009. Same A1, the new Ralink RT3052F processor 384 MHz and doubling RAM. Connectors and appearance remained unchanged. Incidentally, these audits were sold in Russia under the label DIR-300NRU.

In the first modification, in general, little has changed

DIR-300 B5, B6, B7

New iron from previous versions: Ralink RT5350 processor at 360 MHz. RAM and flash memory the same. Between a hardware device are not different. Outwardly B5 and B6 are similar to the previous ones, but the B7 out a new design and are available only in the Russian market since 2012. Also marked NRU.

The rear panel has a standard set of ports

DIR-300 C1

Outwardly, little has changed ventilation grille. Internally - a new Realtek RTL8196C processor at 400 MHz. Ports, connectors and opportunities are the same.

Increasing the ventilation grille - that's the whole "restyling"

DIR-300 D1

Changed CPU index - the Realtek RTL8196E, and the frequency remains the same - 400 MHz. Undergone dramatic changes appearance and, in fact, form factor. The router received a "standing" position. Produced in 2013 Now buy a router D-Link DIR-300 D1 possible for 800 rubles.

The transition to a new form-factor was the fresh solution

DIR-300 S / A1

A completely new appearance. Processor device got from D1. It increased the amount of flash memory up to 8 MB. The other characteristics are the same as that of D1. Produced in 2013

There have already appeared twists and custom shapes

DIR-300 A / A1A

Hardware full copy of DIR-320 with 4 MB of memory, and no USB-ports. The design stands out from the classic "box" and is a cylinder.

The cylindrical shape at first a little surprised users

D-Link DIR-step tuning router 300Which is better to buy a wi-fi (Wi-Fi) router and how to configure it.In a special publication of our portal, we describe in detail how to choose a router. You know what a router, the router is a better Wi-Fi, or the nuances of selection, how to choose and how to connect the router yourself.

How to connect the router D-Link DIR-300

Nothing complicated about it, actually, no. First you need to learn some controls and connectors. The front panel LEDs are usually located icons responsible for processes inside the display device:

The front and rear side of the router:

  • power indicator. Standard for all kinds of devices icon;
  • connect the indicator to the Internet. Usually this icon in the form of the globe;
  • Wi-Fi indicator. Several waves. ON - connected, blinking - there is a data transfer;
  • LAN-port LED. They may be numbered in accordance with the ports. By analogy with Wi-Fi, if you blink - it sends data off - connected.

On the back panel there are 4 LAN-ports (black or blue) and 1 WAN-port. Last is yellow and may be labeled as the internet or wan. More on the rear panel has a connector for power, reset button, and some revisions - WPS button. Included with the router is normally supplied special cable blue. He has already crimped on both sides and is ready to use. With his help, and perform the initial configuration of the router.

It connects to one of the LAN ports, to which there is no difference. The second end to be inserted into the computer's network card connector. Connect the power and turn on. On this physically connect the router D-Link DIR-300 is completed. Once the wireless network is configured, you can disconnect the cable and use the Internet over the air.

How do I reset the router D-Link DIR-300

The router provides a system of emergency return to the default settings, if you suddenly something went wrong. There are two ways to do it - through a web interface, which we describe later, and physical - with the Reset button on the rear of the unit. In order to activate the reset process of D-Link DIR-300, you need to take a thin object - a paper clip, a match or the like, press the button and hold it for more than 10 seconds. All settings will be reset to standard.

How to configure a router D-Link DIR-300

All configuration DIR-300 occurs in the web interface of the router. But in order to get into it, you need to connect the router to the computer network connection. To this end, we at the beginning of the article inserted into both devices dedicated cable. Now let's see how it all set up.

The preparatory phase - Set the connection to the operating system

Once the cable has been inserted into the sockets LAN-ports of both devices, the operating system should detect and automatically create a network connection to the router. At this stage a little trouble can occur: the network connection is not present. This usually occurs due to incorrect installation of the IP-address in the settings of the network connection protocol. The fact that the router using DHCP technology every time you turn on or connecting a new device distributes IP-addresses at random. That is, one can get to 192.168.0.2, and the other - 192.168.0.102. And in the computer settings can be the address specified manually, and even from a different subnet. Therefore, in the absence of the connection must first check this option. To do this, go to the Control Panel and find the option "View network status and tasks".

Control Panel

Then, in the networks list, select the "Local Area Connection". click "Properties" in the pop-up window.

Properties and Network

In the new window, select the "Internet Protocol Version 4" and click "Properties." Finally, open the right thing. Here you need to check whether the switch is in the "Get IP-address automatically" and "Obtain DNS-server address automatically." If not, both are activated.

IP properties

How to configure a router D-Link DIR-300

Once the connection is displayed, you can start configuring the router itself. All manipulations are carried out in its web interface. Therefore, you need to start from the entrance.

Login to the router interface

To enter, we need any browser. Opening it, you need the address bar enter the IP-address of our router. By default, this is 192.168.0.1. Less often 192.168.1.1.

Log in to the admin panel

Open the login window. Here you need to enter your login and password. Typically, a pair admin-admin, less often - admin and a blank box or 12345. After entering the password and login we get into the holy of holies - the administrative panel of the router.

By default, a page with information about the device. Here you can see the various service data: revision, firmware version, network name, MAC-address. Sections on the left defines the category of settings.

First page admin

Setting up the Internet connection

To configure the network, oddly enough, we need to go in the same section. Here it is necessary to select a subsection «WAN». In the lower right corner there is a button "Add". She and activates the process of creating a new connection to the Internet.

Adding network

The system immediately prompts you to select the type of connection. For most cable providers it is PPPoE. Further, for easy connection of the Internet, we need all three points: the already mentioned connection type, user name, password and confirm it. In the fields of the login and password, we specify the data that the provider issued. They can be found in the contract or its annex. Click "Apply". Thereafter must blinking icon globe on the front of the router.

Creating a connection

Setting up Wi-Fi-router D-Link DIR-300

Now you need to give wireless traffic. For this purpose there is a special section of Wi-Fi. In the section "Basic settings" and the first part of the configuration of the wireless network will occur.

Firstly, it is necessary to include, if it suddenly turned off. Therefore, we check whether the tick "Enable Wireless". Then you need to specify the name of the network, which will be visible in the list of available networks. For it is in the SSID field. The default router can substitute your name, which can be used without modification.

In this menu, you can draw your attention to two points: "Hide Access Point" and "Wireless Mode". With the first, you can hide your network so that access to it was in name only, that is, it will not appear in the list of available networks. The second determines which mode will operate the router. Recommended - mixed to different types of devices to connect to the network. In fact, the modes - a data rate options.

Wi-Fi settings

click "Apply" button after specifying all parameters.

Check the connection status

Check network availability is now very simple. Disconnect the cable from the router. Turn Wi-Fi on your device, we find our network and try to connect. If you have set the flag "Hide Access Point", you have to find the item "Connect to a hidden network" and manually specify the network name.

If the Internet has become available, it means that everything is configured correctly. However, there is a problem - the network does not have a password. This means that it can connect to anyone. Including the attackers. It is necessary to set up.

Setting a password on a Wi-Fi router D-Link DIR-300

For password meets the subsection "Security Settings" section of administrative Wi-Fi router. By the way, you can go to the bar and through a wireless connection, again typing in the address bar of the browser 192.168.0.1.

Security Settings

The settings are not so much. Firstly, you need to set the type of authentication. The most protected today considered WPA2-PSK. Then you need to specify the password in the field. All. Now we have to remember the password provided and click "Apply".

How to create a backup copy of router settings

Sometimes you may need to restore already saved settings after unsuccessful flashing, accidental discharge or a system error. To do this, you can create a backup copy to be stored in a safe place the hard drive, and if necessary to restore the system. It is responsible for this "system" and the subsection "Configuration" section. Items for the operation of creating a file and load it and called. Push the button, specify the path on your computer and save. To restore the data, perform the same operation. It's simple.

Configuration

What to do if you want the router firmware

Firmware - this is quite a serious operation on the router. Her need may arise when the machine began to fail, to lose Wi-Fi or reboot itself. And if does not help even a factory reset, you may have saved it in the firmware.

Another reason may be a desire to flash the router to use full force of its potential. The fact is that the original software uses the iron is balanced without requiring him to marginal productivity. The custom firmware disperse it in full. However, this approach has a significant drawback - it's overheating and failure of the supply chain.

Describe the process of firmware we will not, because for each audit used its approach and its tools. However, a few recommendations can be given. Do not run immediately to reflash your router, because you can first try to reset it to factory settings. Almost all models have built-in update mechanism that can be activated manually. Before you upgrade the router D-Link DIR-300, be sure to make a backup copy.

system update

And if you decide to flash your router, then use the instructions on the authoritative sources. For example, the official website has basic advice and guidance. Also 4PDA forum has a huge database of knowledge, firmware and tools for each of the audits presented DIR-300.

Features a router settings D-Link DIR-300 as an example Beeline provider

Beeline to connect to the Internet using L2TP type. Accordingly, methods of creating such a compound will be a little different. However, all the procedures carried out prior to entry into the admin panel, you can take from the usual settings of the router. Next we will need to get WAN section under "Networks". Here you need to specify the L2TP + Dynamic IP. The field with the name, you can specify that you want, anyway you will see it only here, in the admin area.

Setting Beeline

Then you need to find the field «VPN-server address" and enter the address. Usually it is the same - tp.internet.beeline.ru. Next you need to specify a username and password. They must be specified in the contract.

Setting Beeline

Other settings can be left as is. To learn how to set up Wi-Fi, we have already mentioned above, the procedure is the same.

Features settings of the router D-Link DIR-300 as an example a provider Rostelecom

Instructions for setting up a fully coincides with the setting PPPoE-connections described earlier in this article. However, you should check out when you create the connection to point to Keep Alive was ticked. Along with the Internet, Rostelecom allows you to configure and IPTV. This is done in subsection WAN section "Network." We need to find a place here in the types of connections, called IPoE. However, in the new firmware is not. But there is a static IP. It and choose. Set in the MTU field in 1492.

Setting IPoE for Rostelecom

Further, in the IP-address fields put 1.1.1.2, a network mask: 255.255.255.0, Gateway address: 1.1.1.1. In the "Miscellaneous" leave only tick the "Enable IGMP».

Setting IPoE for Rostelecom

Then have to go back in the "Advanced" section, subsection "Miscellaneous" and make sure that a check mark in the IGMP, version 2. That's all.

Prices for routers DIR-300, commercially available

PhotoCharacteristicsPrice (as of April 2018), rub.

DIR-300 D1

Transmission speed: 150 Mbit / s. Frequency range: 2.4 GHz.800

DIR-300 S

Transmission speed: 150 Mbit / s. Frequency range: 2.4 GHz.990

DIR-300 A

Transmission speed: 150 Mbit / s. Frequency range: 2.4 GHz.1 000

Our editorial staff has prepared this manual specifically for its readers. We look forward to your comments and feedback on the article.