Any person in the course of his life to travel, and since the invention of the wheel, it tends to make the process as much as possible more comfortable, improving and creating new products, one of which is an orthopedic pillow on the road in the form of pits.
This article is an example of the manufacture of orthopedic bone pillows, from sketch and pattern to the finished product, which has a positive feedback among the people who have tried it. The indispensable on the road and do not take up much space, comfortable and cozy.
Comfortable and functional pillow-bone will help get rid of fatigue and forget about the sensation of pain in the cervical spine
Content
- 1 Where to begin?
- 2 Pattern orthopedic pillow
- 3 Cutting road cushions
- 4 Sewing cushions bones
- 5 Videos: Sew orthopedic pillow-bone
- 6 Photo gallery of beautiful and comfortable pillows, stones of different materials:
Where to begin?
Production of orthopedic bone pillows should begin with the choice of fabric, the material, which is planned to place the filler. In this regard, it recommends the use of:
- mahram.
Soft and fluffy terry cloth products
- fleece.
Lightweight and hypoallergenic synthetic fabric - fleece
- tight jersey.
Dense jersey high quality
Although it is not necessary to rush to the store and choose your favorite fabric, not after reading this article. It may be amiss tissue from unused bathrobe or towel. The World Wide Web there are cushions of silk and even leather.
In addition you will need: yarn, needles, scissors, thick cardboard, a ruler, a pencil and a little patience.
For the manufacture of pillows you need materials and tools
Pattern orthopedic pillow
The first step is to produce the pattern, based on which to build the entire subsequent process of manufacture road pads.
Template for making a pillow-bone
To this end, it proposes a phased follow these steps.
- In a dense sheet of cardboard, with dimensions not less 40h20 see, hold the vertical axis of the separating paperboard web into two equal rectangle.
- Exactly in the middle of a vertical line drawn mark the center, and draw a horizontal line through it. You should get four equal rectangles.
- The vertical axis measure 18 cm from the center in both directions. Put the two marks.
- The horizontal axis to measure 5.5 cm from the center in both directions. Also put the mark. This is the narrowest part of the bone.
- From the base point to 18 cm on the vertical axis to retreat 3 cm towards the center, to make a mark. On the other side of the figure to repeat the operation reversed.
- After the resulting point of a horizontal line length of 9.5 cm, in both directions. Tick. This is the widest part of the bones.
- From the point of 18 cm 1.5 cm in a retreat direction from the center, a horizontal line.
- Check that all the marks are symmetrical relative to the axis, should be a mirror image.
- Connect all the marks obtained by the contour of the bone.
- Sharp scissors to cut out the pattern on the paper get a loop.
Print out the template and 4 combine these components in accordance with a pattern, we get one of the three sides of the pillow
Cutting road cushions
Cut out parts pillows, consider seam allowances
Turned out the pattern of the future product should be attached to the inside of the previously selected material and the contour to hold a continuous line. By using sharp scissors, cut the workpiece along the contour products. no need to make stock on the seam.
Pre-make the notch in the field of combining parts
For the manufacture of orthopedic pillows road, it will take three such blanks on the pattern.
Sewing cushions bones
two pieces of shear pins face to face
Sewing products begins with the fact that all three correctly folded blank to get the bulk form of the stone.
Grind cleaved details
Seam starts at the narrowest place of the bones on the inside of the material, then the perimeter and ends in the same place. In total, should have three stitches.
We put into the seam loop of the tape or ribbon
It looks like a nested loop
When tailoring the product, it is recommended to use a sewing machine, however, is not a name for the latter, you can get a needle and thread, although this will be more time-consuming.
We grind the notch by notch until only one side of the part
Reserve in the seam a little hole for a reversing parts
Always leave stitched not place 15-17 cm, designed to evert the product face material.
Pin up the third part of our pillows
Pritachivaem third part of our design, we remove the needle and make notch on all the bends of joints
Sewn on the pattern you need to fill the blank filler for the role that will fit well:
- remnants of foam, 2-3 cm in diameter;
Pieces of foam suitable for filling our pillows
- sintepon;
Furniture and textile filler - sintepon
- hollofayber.
Balls hollofayber - resilient elasticity and shape retentive filler
We gut-wrenching our case through the left hole
Stuffing a pillow suitable vehicle
Do not advise too tightly fill orthopedic pillow, it should be moderately soft and dense, generally comfortable.
It remains the last stitch and the product, in the form of an orthopedic bone pillows road - ready!
Opening blind stitches sewed
The entire procedure takes less than an hour, and the result is as they say "on the face", more precisely on the neck. Which is not just to say thank you for the opportunity to enjoy such a wonderful product.
Our pillow-bone is ready, you can use it for recreation
According to this principle can be made a few pillows for the whole family
Today, almost everyone uses such traffic orthopedic pillows, this one will be surprised. But now there is an opportunity to own hands to make a pillow with individual style, one has only to experiment with the choice of material and the filler.
