Decor dressing room mirror with your hands: how to start?

You probably saw on TV make-up rooms models and actors with a professional make-up table and drew attention to the lighting mirror.

Bright lights are located on the perimeter of the mirror frame and the light is directed at the person. Such a method of lighting used Studio photography to avoid the presence of undesirable shadows on the face. It is easy to make such a decor mirror with your hands at home.

Design with frame of spots will look stylish and in the hallway and in the bathroom and in the bedroom above the dressing table. Getting Started.

Correct tool selection easier to work

Quality any case up to 50% dependent on the availability and expertise tool. In everyday DIY hardly factory equipment there, but it is possible to dispense with expensive materials. Production of frames for mirrors is not as difficult as it seems at first glance, and a set of tools there in every home. We need to do:

• electric drill with PH2 bat
• Drill for wood and concrete,
• under evrovinty hexagon diameter of 3 mm.
• tape measure, pencil, ruler, set square,
• curly and flat screwdriver,
• miter box with fine teeth hacksaw,
• crown with cutters on wood,
• pliers and wire cutters,
• bar with sandpaper,
• tray for paints and varnishes,
• large clean sponge to apply the varnish.

When you select a drill is not necessary to rely on more expensive models, they are designed for high load and continuous use for a few hours. inexpensive tool fit at home. You can purchase high-quality second-hand drill, it will last longer than the new cheap. In no case do not take power tools from a neighbor or friend, if it will burn you have to buy and bring back new and themselves left with nothing.

Miter will make a saw cut end elements at an angle of 900 and 450 for the subsequent assembly of the frame. Hacksaw to trim costs with a fine tooth pick, it would make a clean cut without chipping. The cloth should be broad and perfectly straight. Typically commercially miter box comes with a hacksaw.

For high quality of work it is necessary to monitor the availability of hand tools. It is very difficult to evenly tighten the screw with a screwdriver whipped splines or without spoiling the material blunt Drill hole drill. Beauty products is lost on such trifles.

Preparation of component frames for mirrors

Primarily need wood panels and bars. The elements must be otstrugany and polished, to have the texture of a minimum of knots (better without them), you need to choose the tree is dry and smooth. For smooth front part suitable solid casing, but its thickness should be not less than 15 mm., Width of 100 mm. Meters boards can be calculated using the formula: Length + width side of the mirror frame multiplied by two for trimming the stock + 10 - 15 mm.

Before you begin, make a list of necessary materials for our decor:

• wooden bar 20 x 25 and 20 x 40 mirrors the perimeter of,
• wooden plank 120 x 15 to the inner frame on the perimeter of the mirror,
• metal assembly area 20 x 20
• Furniture corner 60 x 60 x 10 for connecting the facade angles: 8 pcs.
• hangers for wall mounting 2 pcs.
• evrovint (konfirmat) 5 x 50 with decorative caps,
• 13 mm long screws. and 51mm.,
• double sided tape for sticking mirrors in the frame,
• and blue paint on wood,
• Fittings halogen spots with light bulbs,
• PVA is carried out 2 x 1.5 with an electric plug,
• Furniture Mortise switch.

Strap length 120 x 15 corresponds to the length of the facade decoration, wooden blocks should be 10 cm. more. Particular attention should be paid to the products humidity, wet wood over time, lead and your frame will become worthless. Dry elements are lightweight and emit a dull ringing when tapped.

Azure is designed for tinting and highlight the texture of wood. Choose the color of your choice can be to showcase samples in the store. The varnish is better to take a nitrocellulose NC. The smell of it is quite pungent, but the drying time of materials: 1-2 hours. Furthermore it is well raises unpolished surface villi, after applying the first layer is necessary to clean them with fine sandpaper.

Number of lamps is calculated taking into account the distance of 30 - 40 cm on the four sides of the frame. Diameter mortise valves 50 mm. The wiring diagram of the lighting unit, it is desirable to insert the protection of halogen lamps, it will prevent frequent burnout of lamps.

So, we proceed to perform!

Skillful execution of the work achieved by performing a large number of additional actions, attention and patience. Do not hurry, it is better to spend time on the precise execution of instructions on what alterations poor performance. So our frame for the mirror is assembled and disassembled several times.

Let's start with the front cutting board frame. First you need to make labels for mechanical cutting 450 on each of the four parts, the distance between them corresponds to the side of the rectangular shape mirror with a margin of 1 mm., the ends must remain equal segments by 15-20 cm. With the miter box saw off decor detail by marking an angle. Now, if the layout should get very close frame framing glass.

Further distribute lamps at a distance of 30 - 40 mm. defining the middle of the width of the jamb. Cutter drill holes in wood with a diameter suitable to the size of spot reinforcement. The workpiece must be well secured.

Putting the frame via the flat parts of furniture at the inner edge and evrovintov below and above the outer edge. Evrovinta drill holes for a diameter of 4.5 mm. and zenkuem under head 6 mm. Should get accurate mirror frame without slots and the teeth on the corners of elements with circular slotted contour.

From the preforms measuring 120 x 15 make a similar manner a second frame whose inner perimeter should be 10 cm. less than the height and width of the window. These fields are used for gluing mirrors. At the outer end fastened SCREW 20 x 40 block so as to provide ledges 25 mm. Now combine the two parts by means of screws 3.9 x 51 from the rear side. To fill the inner slit is applicable timber 20 x 25, after attaching it to the facade on the corners. The product after assembly should have the form of a box with wings 10 mm. on the outer perimeter of casing and 50 mm. inside.

Parse frame for painting. We are first applied azure dipping a sponge (foam can take loofah) and continuous wiping motion of the workpiece surface, including the ends of the slats and eclipsing bars. After soaking azure varnish 2 - 3 layers. The first layer is sanded P600 grit sandpaper to remove small villi.

Give the required time to dry the coating and collect inlay mirror, adding to the structure of the wall mounting suspensions. On the inner surface of the sticking double sided tape and insert a mirror. If the product is large, it is better to do it together.

Through the drilled hole on either side of the wire within the plant under illumination. Next appropriate place furniture switch, cutting and skipping through one of the two strands.

Next fixtures are connected in series and inserted into the holes spots decor, hang a mirror, made with his own hands in place, insert the plug into the socket and call households to take the job.

Video: DIY dressing room make-up mirror with your hands