The inlet hose washing machines: types, variants of its extension, the reasons for failures and remedies

click fraud protection

The water inlet hose to the water supply in stiralkaThe water inlet hose - the product, which is responsible for water filling the washing machine. water hose differs from the branch drain that is manufactured using a unique technology of reinforced PVC, rather than plastic. The design of the inlet hose to the washing machine is made of steel wire or strands of synthetic fabrics, which makes it very durable and to withstand the flow of water under pressure. Manufacturers in the manufacture of hoses for washing machines may use different materials, but the technology and the design remains unchanged. The inlet hose is sold complete with a washing machine, but it sometimes happens that he wears before the washing machine itself.

Content

  1. types of hoses
  2. What to do if a leak is detected
  3. How to lengthen the inlet hose
  4. The role of the pipe in the washing machine
  5. Repair and cleaning of the filler neck

types of hoses

The hose for supplying water into the washing machineHose to the washing machine is tube with plastic nuts and fittings and it has a marking, which contains information about the operating pressure and temperature. One part of it is connected to the water supply, and the other directly to the washing machine itself. Bona fide producers set at the junction with the pipe fitting extruded sleeve of metal.

Ducts for filling water into the washing machine are:

  • fixed length which is from 1 to 5 meters;
  • in the bay to 10 meters in length;
  • telescopic, increasing in size, with built-in Aquastop system, which is able to protect the bathroom from the flood.

The best of its kind found inlet hose with Aquastop systemAs it can withstand the water pressure at the bay 70 and has a unique water supply system in the case of overlapping the gap duct.

It should be noted that the inlet branch length should not be more than 3 meters. Connecting the water inlet duct is possible before the mixer or set it using the HERZ-TS on the float valve toilet tank toilet. For these two options in the plumbing departments can find special accessories that simplify connection hose Bay washing machine.

What to do if a leak is detected

There are several reasons because of which the water inlet hose can flow:

  1. The most frequent reasons because of which the water inlet hose can flowLoosening threaded. This may be due to the fact that the rubber gasket after a certain time may become deformed and lose elasticity. Solving the problem - you simply replace the rubber seal.
  2. Improper positioning of the expense and the impact of the weight of the hose on the gasketThat leads to its weakening. The flat part of plastic, which is adjacent to the strip, must be perpendicular hose.
  3. It may happen that a leak occurs in the place, wherein the plastic part of the duct is connected with an iron girth rubber portion. In this case, the loss of elasticity of the material and weakening of the girth of pressure may occur. It is necessary to firmly fasten the inlet hose on the wall of the washing machine. If the leak persists, replace the device for the waters of the bay.
  4. Happens that streaming occurs on most of the rubber part. This may be due to long-term operation of the hose or by mechanical action. It is difficult to immediately detect the injury, so you should dismantle the hose, and in good light to examine it carefully. Many in the event of this problem using glue, but can be seen with certainty that this option is short-lived, and it is better to carry out the replacement of the old inlet hose on the new one.

How to lengthen the inlet hose

If you can not make replacement of the old inlet hose water supply to the new one, but longer, there is a fairly simple and very cost-effective method of its elongation. This will require an additional hose and a brass nipple for three quarters of an inch. Brass nipple is a metal connecting pipe with thread. For a start, disconnect the inlet hose from the washing machine. Next, you should combine the two extension duct via a pin, which in turn will act as a connector.

The role of the pipe in the washing machine

Pipe, as well as any other item in the washing machine, plays an important role in the normal functioning of it. Due to the filler neck, in the car enters the water and household chemicals intended for washing. The machine has a spout, which is responsible for the discharge of water. In cases with newer models installed additional fittings, which are intended to remove the foam and steam. To a washing machine worked without interruption, every pipe must be installed correctly and safely.

Sometimes the cause of damage to the washing machine is a breakdown of the nozzle, which is eliminated by replacing it. But in order to increase the time of its operation, it is necessary to apply preventive measures. Nozzles should be periodically cleaned in the same way as the garbage filter, as a result of prolonged use plaque may form inside it.

Repair and cleaning of the filler neck

The reasons for leakage of the inlet hosePipe is located directly under the body of the washing machine, so it should first make out. There should be observed a certain sequence.

You need to make sure that blocked the flow of water into the machine. Further, the washing machine should be disconnected from electricity. Deleted compartment for receiving powder. Withdrawn trash filter. It is necessary to put the washing machine on the prepared cover or cloth on the free floor area. The machine should be careful to put the motion to the side wall.

If the machine water is present, it should be removed. If you do not, you can do much harm to the control module of the washing machine. Next, using a screwdriver removing the top cover of the machine can be seen in the upper left corner of the rubber tube that goes from the Gulf water. Pliers gently, trying not to damage them, as they will be mounted back to be let go and move to the middle of the pipe clamps, which hold it. Next, remove the filler neck, to determine its status. If there is a blockage, they need to be removed if there are damages, the right to buy a new tube.

Washing performance is directly dependent on the component parts of the washing machine and the proper care of them. If, due to breakage had occurred to carry out repair or replacement of any parts should be very seriously approach the solving problems, and in the case of buying new parts are not stingy and opt for better quality materials.