How to clean the hood from fat: domestic cleaners

Clear hood from the layer of stale fat - is not easy. Therefore, every woman knows that you should not run it, but should be cleaned in time, the extent of contamination. It's hard to do, but still possible. There are ways to help clean up the kitchen hood of oil, so that it shone with cleanliness.

The preparatory phase of the work

Before you wash hood in the kitchen of fat, you need to switch off the power, then make a gradual dismantling. To do this, push fixing clamps and the cover is removed from the slots. Some hoods have covers, so I go to take out the filter, which may be two.

Pipe leading to vent if it is removable, dismantling. Then remove the air filter. Dismantling is carried out according to the instructions to the hood. According to the work of cleansing begins the conclusion of this process. If some items are not removed, they are washed in a secured position. The surface is washed with the device with a solution, which is prepared based on the dishwashing detergent and water in a ratio of one to four. The solution was immersed and washed sponge contamination. Much attention should be paid to laundering the hood filter, which has the form of a lattice.

fresh pollution

Simply clean the cooker hood in the kitchen grease, if contamination appeared recently. If the electrical device operated only one or two months, you can clean the filter from contamination withvia:

• the usual means for washing utensils. For this it is necessary to prepare the same solution as for the purification drawing surface, and pour it into a pan, and then immersed in the prepared fluid filter. Leave it for an hour or two, then get it and rub with a stiff brush. If the layer of fat remain, it is necessary to pour boiling water over the bars and again brushed with the means. If, before the end of the clear fat from the filter failed, the procedure is repeated from the beginning.
• composition of baking soda, vegetable oil, in the ratio of 3 parts to 2. The consistency should be like thick cream. It is applied to the surface of the fat and leave to dry. After that, the bars should be rubbed with a dry brush. Soda will be removed, and drags along the body fat.
• composition of baking soda and citric acid. To wash lattice drawing, via a sprayer or sponge is applied to a solution of detergent and then preparing a separate mixture of equal parts of baking soda, pineapples and water. Should get much foam, it is applied to the grille with a sponge and is kept for the time of exposure. It is possible to do otherwise. The cleaning composition is poured directly onto the mesh, it is then sprayed water. The chemical reaction of the acid and alkali cause fat to separate from the metal. After 30 minutes, the filter was washed with running water.
• 9% vinegar. Before you start to wash the hood, it is diluted with water at a ratio of one to one, and then applied to the clogging of the mesh. After 5 minutes of exposure vinegar with a sponge should be washed off with the fat. If the pollution is very serious, and failed to clear the first time, you can apply undiluted vinegar and leave for 10 minutes, then rinse with a damp sponge.
• lemon. The fruit should be cut in half and rub the cut surface of the filter. After some time after exposure to juice washed away with the fat. If there is no lemon, come to the aid citric acid. Half sachet powder is mixed with a tablespoon of water and rub bars.

If the filter is small, it can be placed in the dishwasher. From the first time you can not achieve purity, so the procedure is repeated once or twice.

Purification by boiling lattice

To clean the cooker hood in the kitchen, if the above methods did not help, apply more effective method. The large pot (5 liters) was poured water and bring it to the boil, then poured 2 big spoons of baking soda and soap half piece previously grated using a trowel. For this procedure, you need to choose a solid brown soap, as white and liquid counterparts do not have the necessary properties.

In boiling water filter is lowered and it is boiled for 5 to 10 minutes. Then, turn off the flame and without removing water from the lattice, waiting for the solution to cool. After that, the grid is removed and scraped off the remains of grease with a brush.

If the filter is not entirely fit in the pan, it is processed in parts. Boil will need to first one side, then the other.

Cleaning the filter is ready to make

How to clean up the hood of the fat, the professionals know. Special formulations for cleaning filter and the area stretching will help to quickly and safely clean up the mess in the kitchen. List of body fat solvents as follows:

• universal properties has cleanser entitled "Selenium". Fluid is based on caustic soda, packaged in a container with a spray. The composition is applied to the soiled surface and left for 15 or 20 minutes after which the fat is removed with warm water.
• Another means is a gel "Milam Antizhir". It is also sold in the form of a spray. With a sponge gel is rubbed into the grating surface and, after 5 minutes of exposure with the fat rinsed under running water.
• Recognized as a powerful tool zhiroudalitel Unicum. It corrodes mud layers instantly. For this spray composition is applied to the grid after 20 seconds and it was washed with a wet sponge under warm running water.
• cleans the filter surface cleaner Amway oven cabinet. The gel consistency well impregnates the mesh surface, filling all recesses. This preparation is produced from a brush, which it is partitioned by filter hoods.

Last cleaner is very easy to use, it also allows you to lubricate the vertical surfaces of the appliance. Thick consistency well delayed, so this tool has been successfully used for the purification of extracts of old, where you can not remove the filter. To clear the hood from the fat by this means, the gel is left to act for 5 or 10 minutes, after which the composition is rinsed with stubborn grease under running water.

After cleansing the grid using household chemicals recommended to do the procedure again and leave to dry. Then, without washing agent, the lattice is put in place, and begin to operate normally. The next time the treatment will be less problematic, as the fat will be deposited on the cleaning composition.

soda ash

The alkali concentration in the soda ash is higher than in conventional food. Therefore, it is better suitable for domestic use. Recipes application:

• By drawing a lattice placed in a pan and rub on both sides of the particulate soap. Poured into 5 liters of hot water to the filter is completely immersed in it. After that, add 5 tablespoons soda ash. Baking the lattice is put on the plate include fire, heated to boiling, whereupon the contents refluxed for 5 minutes. The longer this time, it is not necessary to keep the fire, as they can come into disrepair plastic clip. After this time, take out a filter and washed under hot running water. You can rub the brush, if there is a zone with the remaining fat.
• Another recipe with soda ash: from the economic soap and soda is added malic acid, it is able to enhance the effect. The pot volume of 5 liters is poured water, is added a shaving soap, ground apple and 5 large soda spoons. The composition should boil, after which it is poured from the filter pan. After 30 minutes of action fluid is drained into the toilet, and the grid was washed with warm water under the tap.
• Quick effect can be expected from the composition, which are the components of soda ash, washing powder, Clerical glue. The latter consists of - sodium silicate, which is often manufacturers add in washing powders. Stationery adhesive enhance cleaning quality of the first two components. The recipe is as follows: 6 large spoonfuls of soda ash is combined with a spoon detergent powder, laying in a mixture of 2 large spoons glue and water glass is poured. The composition is poured into a bottle and shaken well. It can be applied to the dirty surface and leave for an hour to act. Thereafter, the filter is washed under hot running water. Fat is washed away together with the composition without effort.

Tools for pipe cleaning

If the hood is not being cleaned for a long time, remove ingrained oil will be much more difficult, as in the operation to extract the kitchen dirt compacted and become hard. Often simple ways to get rid of dirt with detergent and boiling are powerless. Therefore there is a need a more aggressive compositions.

Thick layers of fat means able to remove for cleaning of drain and sewer pipes. Before using such means must ensure that the kitchen sink is made of a stainless material, since other types of materials it means may spoil.

Previously, before using a cleaning agentShould study the instructions to him. The manufacturer recommends a solution to prepare a kitchen sink, and then dip the filter by drawing it. Immediately after that, the last action violent chemical reaction to occur. Body fat will just explode and be separated from the grid. Wait until everything calms down, and drain.

If you can not use the sink, spend grid cleaning in baking. After stopping the chemical reactions carefully pour liquid down the drain.

Such an aggressive cleaning should be carried out only in exceptional cases. Before you apply this method, better to try to clean the grate by other less radical methods. To do this, try to avoid the formation of large fat layers, and it is better to clean every two or three months sparing means.

Security measures

Facilities for cleaning exhaust contain harsh ingredients that can damage the skin. that to prevent burns and injuries, You should use rubber gloves. It is also worth to protect your eyes with glasses and wear long-sleeved clothing to avoid dripping on exposed skin. The work is desirably carried out in a well ventilated area, isolated from the others. Pre costs limit the access of children and pets in the room where the exhaust cleaning will be carried out. Particular care should operate with means for cleaning and drainage discharge tubes.