Before the advent of electric light in the house provides a versatile kerosene lamps. Current models of such products can impress the original design, which perfectly fit into any interior. But if the attic has rusted from time to time the lamp, then each person can perform the restoration of the rarity of a kerosene lamp. The process itself is not only affordable, but also interesting.
Content
- The principle of the device
- classical transformation
- Fight with soot
- The original approach
- charging rules
The principle of the device
Standard kerosene lamp favorably simple principle device and high reliability, which is very similar to the common oil appliances. In a special kerosene tank is filled, the liquid dispensed is fed into the combustion zone.
In some cases, the burner can be supplied by means of flue gases and air. The coordinated operation of the product is provided with special flame protection. High frame for the suspension and movement lamp.
The traditional oil lamp consists of the following components:
- tube with a cap;
- bottoms;
- a fuel tank;
- rack;
- special tube for the wick;
- Lamp bulb of glass;
- Universal insert required to adjust the position of the wick and the cone opening (light intensity control).
classical transformation
Do not be in a hurry to throw out the old lamp, which is covered with rust and no longer used. If a little effort, such a product can be just a few hours to transform into a stylish and romantic decor items. Restoration of the rarity of a kerosene lamp is possible even if rusted in several places and began to leak. And such a thing can be turned into a beautiful accessory.
Primarily you need to thoroughly wash lamp with the detergent. After that, it is necessary to rinse with clean water and dry thoroughly. Wet sandpaper all metal sections must be carefully cleaned. Particular care needed to treat those areas, which are covered with a thick layer of rust.
This is followed by rubbing the lamp clean cloth dipped in solvent. After thorough drying the product is covered with paint from spray in several layers. It is best to choose a primer on metal. Each layer should dry well before re-treatment. The lamp can be painted in absolutely any color - depending on your preferences. It is desirable to use cartridges, since in this case the material falls evenly as possible.
To the product retrostile turned in, the final layer must be to the effect of copper. After all these steps, the lamp will acquire a spectacular appearance and perfectly fit into the interior.
Fight with soot
Soot tends to occur when the flame height too high. If the normal adjustment have failed, perhaps a little wick is bent. Eliminate the lack of pretty simple. Sharp scissors to cut a strip of wick to the top of it was even possible. Otherwise you will have to replace kerosene.
The system can smoke after the restoration, if before it for a long time did not work. You can pour a little salt (a few grams) in a container of flammable liquid.
To an updated product correctly and safely operate, must adhere to the following guidelines:
- You can not put a working lamp on the table.
- Do not experiment with flammable agents. Experts recommend using only kerosene and lamp oil.
- Hanging the product should not be placed closer than 80 cm to the ceiling.
- It is impossible to close the opening in the glass, which serves to remove formed gases.
- Prohibited transfer product with a full tank of kerosene, as even spilled drop can cause a fire.
The original approach
For the restoration of an old oil lamp can be approached creatively. At the first stage the product must be completely cleared of fatty plaque and dust, for these purposes, you can use gasoline or pure alcohol.
the lamp It can be covered by refractory or acrylic paint. To impart additional elegance kerosene tank can be covered by a mosaic or make multicolored decoupage. If the wizard versed in electricity, it is possible to replace the internal parts of the lamp on the power, then a modified design can be converted into a real masterpiece, while not requiring the use of kerosene.
Refurbished product will perfectly fit into any interior. Therefore, finding the old lamp, no need to rush it throw.
If the owner of a rarity not want to engage in such work, then he can just sell the thing. Kerosene products are in great demand among collectors.
charging rules
To fill the tank with kerosene, you easily pull up the protective glass, while holding the lamp itself. Unscrew the burner, turning it counterclockwise. The container must be placed watering and gradually pour a flammable liquid. Then you need to gently screw the burner on the position of the place and the filter is immersed in the tank.
after loading you need to wait at least 5 minutesThat the filter has had time to soak. It is necessary to adjust the flame height using a special valve (its position changes the rotating wheel). To extinguish the lamp, turn the knob counterclockwise.
If handled properly and proper storage conditions restored the lamp will last for many years.
