How to sew a dress combination?

With the onset of heat, many begin to update the wardrobe. Naturally, the simplest option - to go shopping, to buy everything you need, as a result - leave a round sum of money there. Why not try to sew something yourself? You can start with something simple, so today we will learn how to sew a dress combination at home. Such a dress can be worn in hot weather, supplemented with a summer image or in the cold season used as a lower layer of clothing.

to the contents ↑

Constructing the pattern

Here everything is very clear, cut very simple, there are no fasteners or draperies, which greatly simplifies the process itself. Below we will gradually consider how to sew a dress with a combination of lace on your own.

The final, sewing this product begins with the construction of the pattern. You can either completely create it yourself, or use the finished pattern of the dress and make a few extra darts on it.

Follow the pattern:

1. At half a centimeter, lift the waist line on the backrest and shelf.
2. Reduce the width of the shelf and backrest by 1-2 cm, and in the armhole area - by 1 cm.
3. Extend the shelf and back from the bottom by 5 cm, draw new slices on the sides.
4. Construct new upper lines on the backrest and shelf.
5. Cut a new pattern on the new cuts, close the breast tuck and others, as they will be translated in the side seam into the chest tuck.
6. To make the dress fit tightly on the chest, reduce the new tuck by 3 cm

to the contents ↑

Determine with

material Which material should I choose? Naturally, already traditional for making such things are satin, silk, chiffon. But if you plan to wear your dress not only as underwear, it is better to give preference to light, flowing fabric. For example, viscose can produce a wonderful, not hot, stylish dress-combination. Sewing the most of this material will be even easier.

Important! Although this fabric is considered to be synthetic, it is produced exclusively from natural raw materials. The touch of viscose is incredibly pleasant and soft. In summer, it is not hot in such clothes, because it dries quickly and allows good air flow. Its only drawback is that it crumples strongly.

to content ↑

Sawing and sewing products

Fabrics will need a little less than a meter. Proceed to cutting and sewing:

• Face inward fold twice the fabric, overlay from the wrong side of the pattern with the front sections to the point of the fabric bend. On all slices, make allowances of 1 cm. You will have two parts - a shelf and a backrest.
• Chest darts sweep. Using a sewing machine, grind them, iron the stitches, pull all the darts into the bottom of the dress.
• Treat the side seam with the usual seam. Fold the parts inside out, sweep the backrest and the shelf on the side cuts with the front side. Stitch and iron stitches.
• The product is turned inside out, sweep the side seams. On the machine, mow and iron them. As a result, you will have a beautifully processed seam.
• Now process the top section of the dress. Take a paper pattern to cut out the wrapping from it or on a new sheet of paper, circle the top lines of the product and cut out the edge so that its width is 4 cm.
• With the same allowances, cut out the obtack. Duplicate the obtachka on the fleece, sweep it off the sides. On the machine, grind, iron the seams, lower the cut edge.
• Straps can be made from laces or thin strips of fabric, 3 cm wide. To make the straps even, you need to cut them at an angle of 45 degrees to the transverse and lobes of the fabric.
• Fold the cut strips in half lengthwise, using a machine, run a stitch, receding from the 4 mm bend. Seam the stitches.

Important! The remaining allowances do not need to be cut, because they fill the cavity of the cord, which as a result will turn out to be bulky and dense.

• Take a large needle with a thread, fix the thread on the cord tip, insert the needle into the hole of the cord, pull out the threads, as if turning the cord on the front side. Bretalele can do as much as he likes.
• Measure the length of the strapless, try on the dress, fix by their pins, make on the straps of the serif. Remove excess, swipe them from the front of the dress. On the sewing machine, weld the seams carefully.
• Place the dress and cuff so that you have the allowances left on the side to be grinded. On it, lay a line, retreating 1 mm from the split of the seam.

Important! It is because of this that the seam will later be easier to turn around.

• Turn around the obtachku, then iron. The ends of straps at the same time should be hidden under the obtachku that from the underside they could not be seen.
• It remains to process the bottom cut. Twist the edge of the dress two times on the wrong side, lay a stitch, retreating from the upper fold of 1 mm. Iron the seams.
• As we consider the option of sewing a dress with a lace with a lace, it is logical to decorate the finished product with it. It is not difficult to choose a suitable material, but it can be attached in the middle of the product or in any other place with a sewing machine or manually.

The dress is ready, it remains only to try it on!

Now you are convinced that the combination can be worn not only as underwear. A ready-made dress will look simply gorgeous, the main thing is not to choose for its production the material from which it is customary to sew nightgowns. If you are wondering how to sew a combination under a dress, then you can safely use this idea.