Washing machine does not drain water and hums

Modern housewives do not represent their home kingdom without a washing machine. But, like any other home appliances, an irreplaceable assistant can break down. Do not be upset about this, since at the moment repair at home by service departments is quite affordable, and some breakdowns and malfunctions, for example, when the washing machine does not drain and hum, can be eliminated on its own. In this article we will discuss all possible reasons why the washing machine is buzzing, does not drain the water and will tell you what your actions should be.

to the contents ↑

What symptoms should make you uneasy?

The water from the washing machine must be removed automatically, several times per wash cycle. First, the initial and main wash, then rinse and final liquid removal during spinning. The following symptoms may warn of a malfunction:

1. The water started to drain too slowly, and the subsequent washing schedule is started with a malfunction.
2. Draining of water occurs periodically, that is, not every wash.
3. During washing the water is drained, but at the rinse stage - no.
4. The washing machine hums and does not drain the water at all.
5. The spin mode of the laundry is blocked.

to the contents ↑

Causes of the

unit failure Any of the above faults must first determine the cause of the fault. Sometimes it is enough to simply read the instructions, since in each operating procedure clearly indicated visible faults, under which the washing machine will pump out the water slowly or not at all to lower it. Sometimes such malfunctions in the operation of the unit can be easily corrected by yourself. Consider the main reasons why the washing machine is buzzing, does not drain the water.

Incorrectly selected washing program

During the operation of the machine, be sure to double-check the selected washing mode, as some machines have built-in "no draining" mode. Purely accidentally you could put this program, and if the house has children, it is possible that the lackeys could take advantage of your absence and press the button on the control panel. In this case, the failure to set up easily, just put the right program and the problem with the fact that the washing machine does not drain the water and buzzes immediately solved.

Malfunction of the drain hose

The washing machine can not perform the job fully for the simple reason of the bend or blockage of the drain hose. Carefully examine the drain hose, and at the same time, and clean it for prevention. In case of draining through a siphon, be sure to check it for clogging.

Once the position of the hose is corrected and the dirt is removed, the waste water will pass through. As a result - you will no longer be bothered by the fact that the washing machine does not drain water and hums.

The

filter is clogged. Small and larger parts( items), for example, bones from the bra, pins, coins, buttons, paper, etc., may be the cause of the blockage. The filter should be periodically cleaned, since its clogging can cause not only insufficient water discharge, but also many other malfunctions.

Important! The instructions to the washing machine indicate the frequency of cleaning the filter. Adhere to the rules of operation so that there are no unnecessary problems, in particular such as a washing machine does not drain water and hums, the drum does not spin, the equipment does not turn on at all.

Clogging of the nozzle inside the machine

Sometimes small parts of clothes, for example, socks, handkerchiefs or other small things can be found in the branch pipe that goes from the tank to the pump. As a result, the washing machine will not drain water. Remove the blockage and the machine will start as before.

Pump Fault

External symptoms of pump pump failure may be a muffled pump sound during the draining process. That is, instead of just draining the water, the machine hums and buzzes. Uniquely identify the fault in this case can only a professional specialist.

The cause of the failure of the drain pump can be a natural wear( the average service life is 3-5 years).Another option is that the impeller of the pump could block a small part that leaked through the filter. Without a complete disassembly of the pump can not do, because it could wind and thread, and hair.

A periodic pump failure can serve as a signal for replacing the pump, for example, in the case when the stiralk regularly does not drain the water and does not press the laundry at regular intervals.

Important! If the washing machine does not drain the water and is noisy and hums, contact the specialist immediately, as most likely a replacement pump is required.

The integrity of the wiring inside the

machine is broken. An experienced specialist will determine the wiring problems without any problems. Independently to try to correct such a malfunction, without having special skills, knowledge and experience, it is strictly not recommended.

Fault in the

control module Failure in the firmware or a burned chip lead to the control module( programmer) not giving a signal for draining and spinning. For this fault, you need to re-flush or replace the module with a new one.

Important! Sometimes a washing machine refuses to drain water due to an elementary overload. Follow the washing weight specified in the instructions, then the drum will work without problems.

to the contents ↑

What should I do if the machine does not drain the water?

If you find a malfunction, proceed as follows:

1. Disconnect the washing machine from the mains.
2. Place a water tank with low beads under the loading hatch.
3. Unscrew the pump filter and clean it if necessary.

Important! The procedure for cleaning the filter is described in the operating instructions of the washing machine.

1. If, after removing the filter, water does not drain, then it is necessary to remove the drainage pipe, according to the following scheme:
   • Unscrew the screw fasteners of the drain assembly.
   • Remove it.
   • Loosen and remove the pipe clamp to the snail.
   • Insert the end of the nozzle into the water tank.
   • Carefully inspect the corrugation and examine it for blockage.
   • Assemble all the components and return the machine to its original position.
2. The pump impeller is located behind the filter. Check the rotation of the impeller axis for blockage. For example, threads could wound on it.
3. After you have removed the filter, turn on the spin mode and use the flashlight to inspect the filter hole. If the impeller is clean, but does not rotate, then a pump replacement is needed.

Important! After inspection and repair, be sure to visually check all the connections and fastenings, as well as the electric wires that supply the current to the pump. Start the machine by selecting any washing program to allow the water to flow, then stop and switch to a drain or spin. If everything is correct, then disconnect the machine from the network and check if there is any leaks, and in the future, use the household helper in pleasure.

to the contents ↑

Advice on the prevention of

To avoid problems, in particular such as a malfunction with drainage, take the following measures to prevent damage to the units:

• Always before washing the laundry, carefully check all pockets for foreign objects.
• Do not overload the machine with laundry. Strictly observe the load weight specified in the manual.
• Use high-quality powder in the right amount when washing.
• Clean the pump filter periodically.
• Use a mains filter during washing to protect household appliances from power surges and mains failure.

We hope that you have determined the cause of the failure and found out why the washing machine does not wash water, it hums. If it is difficult for you to correct the breakdown by yourself, we recommend contacting the service center where the cause of the malfunction will be fixed quickly, accurately, and the repair work will be carried out qualitatively and with a guarantee.