Bearing replacement on washing machine LG

If during washing and intensive spinning your stiralk starts to emit a strong noise and suspiciously knock, most likely your device has a problem with the bearings. Replacing the bearing on a washing machine LG is quite a troublesome, but not a complicated matter, which can be done at home. In this article, we will share with you a detailed instruction on repair work.

to the contents ↑

How to prepare?

To save your time, before you change the bearing in the LG washing machine, you must prepare the following set of tools in advance:

• pliers;
• adjustable wrench;
• set of screwdrivers;
• metal stud;
• grease WD-40;
• small hammer;
• set of locating keys;
• car sealant.

After preparation of the tool, take care of purchasing original parts - packing and bearings, for quick and high-quality repair work.

Important! Buy the necessary components can be in the service center, a company store or the Internet.

Also one of the important moments of the preparatory stage is the definition of the most comfortable place for the analysis of the washing machine. For these purposes, a spacious, clean place where all the parts of the disassembled household appliance will fit is best.

to the table of contents ↑

Disassembling the LG

washing machine body In order to replace the bearing in the LG washing machine with your own hands, you will almost completely disassemble the equipment case inside which the movable drum axis is located.

The first stage of the

To begin with, you need to remove the main walls and panels of the stylus, which interfere with getting free access to the internal components of the device. Start by removing the top cover. To carry out this operation is simple enough, because to remove this part you need:

• unscrew fasteners;
• slide cover on yourself;
• slightly raise up.

Next:

1. After carrying out these operations, remove the container intended for loading the powder from the structure.

Important! Remove this part very carefully, because it can collect water, and you should not allow moisture to enter the electronics during repairs.

1. In the niche of the cuvette, unscrew the fixing screws of the top cover, and also uncouple all the wires that prevent its free disassembly.
2. Place the item a bit to the side.
3. To dismantle the bottom panel of the LG washing machine, simply gently bend the plastic latches with a flat screwdriver.
4. Now it remains to unscrew and remove the dashboard and front panel. However, for its dismantling, it is necessary to carefully remove the rubber cuff, after removing the wire clamp.

The second stage of

After disassembling the hull of the stylalk from LG, it is necessary to empty its tank of all fasteners and remove it. To achieve this, remove the following parts:

1. Fixation of the priming valve. Wiring harness for motor.
2. Draining pipe. Upper and lower counterweights.
3. Shock absorber mounts.
4. Branch pipe from water level controller.

Important! After disconnecting all of the listed structural elements, you can still easily and quickly remove the tank.

Third stage

To replace the bearing for the LG washing machine, it is necessary to disassemble the tank and knock out the drum. For this it is enough to unscrew the fixing bolts and divide the structure into two parts. After gaining access to the pulley of the drum, unscrew its fastener.

Important! If some parts are rusted, "sticky" and do not want to be untwisted, then their treatment with WD-40 will help.

Leaning the metal stud to the center bolt, gently tap it with a hammer, which should lead to a gradual knockout of the shaft.

Important! Inspect the surface of the sleeve and shaft for significant damage and wear. If necessary, replace these accessories.

Fourth stage

It's time to replace the LG washing machine bearings directly. To do this:

1. Knock out the old parts from the drum and carefully clean the place of their location from clogs and metal shavings.
2. In a clean place, gently plant the new bearing and press it gently with your hand.
3. After that, gently hammer the piece into its proper place.

Important! When replacing bearings, it is also necessary to replace the oil seals, which must be carefully treated with a lubricant designed for the repair of washing machines and set in place. After the completion of these procedures, collect the styralka, following the reverse procedure.

to contents ↑

Popular errors

Having decided to replace the bearing in the LG washing machine by itself, many admit a number of mistakes that lead to unpleasant consequences, an increase in the duration and cost of repairs.

The most popular tricks of newcomers are the following:

1. The wire breaks while removing the front panel of your washing machine.
2. Damage to the integrity of the cuff of the loading hatch.
3. Thermal sensor wire interruption.
4. Disruption of the "fastened" bolts.
5. Damage to the drum when knocking out its bearings.
6. Damage to the pulley.

Important! If you are not sure that you can perform the necessary actions for repair correctly and safely, then it is better to ask for help from a qualified technician.

In this article, we have told you how to replace bearings on LG washing machines and what is needed for such repairs.