Spare cooler for water: tap and cup holder, a support, a check valve, heating element, pump, and other components, the cup holder

Water cooler - a popular device, which is in each office, and public institutions. Increasingly, such devices appear in residential apartments. Unfortunately, like any other technology, the cooler may be damaged. That can break down in the cooler, how to eliminate the damage on their own and which parts can be bought separately, read on.

Content

  • 1 What can go wrong in the cooler
  • 2 That can be repaired by yourself
  • 3 Spare parts for coolers
    • 3.1 Which can be purchased separately
    • 3.2 Parts compatible with different models of coolers
  • 4 conclusion

What can go wrong in the cooler

Cooler - a device for heating, cooling and supplying pure water. Therefore, main breakdown of equipment associated with the absence of the supply of hot or cold liquid. In addition, the device may begin to leak. Some users also note the appearance of increased noise level when the equipment as one of the problems.

The most likely cause excessive noise during operation of the device - it is incorrectly installed. Perhaps you just want to put the cooler on a flat surface.

If tap water is not flowing, the causes of failure can be somewhat:

  • over the water in the bottle;
  • not removed hygienic sticker;
  • broken tap;
  • formed an air pocket;
  • tube deformation due to the impact of a foreign object in the system, not following the operation requirements, disorders conditions of transportation and storage equipment.

Leaks of water from the tap is also associated with the formation of scale in a tank PETNBreakdowns cup holders for the cooler, thread and applied for manual cooler. Scale appears when users do not conduct regular maintenance kulernoy installation. Eliminate scale it is necessary - it impairs the taste of the water tank and breaks.

When the inside of the tank leak cause of the problem lies in the damaged bottle, Occurrence of microcracks on its basis, tube breakage in creamy valve at the rear or bottom kulernom.

Interesting Online:

How to choose the outdoor cooler with cooling and heating

Rating coolers for water with bottom loading

Water cooler with fridge - Review of the best models

That can be repaired by yourself

you can eliminate the problems outlined above by yourself. If was not completely removed the sticker, you need to turn off the heating and cooling tumblersLocated behind kulernoy installation, remove the bottle and remove the sticker. When the air lock should be lightly shake the bottle and push on the tap hot-water. If the system was the subject of a third party, perform sanitary treatment cooler.

Professional help is needed if the bottle has been damaged or there is a water leak. Then you want to turn off the heating and cooling tumblers and with the help of a sharp movement to remove the bottle. Then, call the technical service and replaced free bottle set.

If there was a pinched tube that delivers water, fasten it also can not be independently. It is necessary to carry out the disassembly in the cooler conditions of the technical service. Otherwise, there is a risk of spoiling the heating element and the adjacent nodes.

When, if not heated or cooled water, requires several minutes or hours is not to use the device. Wait until the indicator turns off and the temperature was heated to 85 ° C and cooled to 12 ° C. Necessarily need to read the instructions for performance. It is indicated in liters per hour.

If water becomes stale or Bottled appears green patina, the reason lies in incorrect installation. On the cooler should not be exposed to direct sunlight. It should be at a distance of 20 cm from the wall. Use apparatus only necessary at room temperature to 40 ° C. To rectify the situation with the green and dirty tank can be putting a new bottle and performing sanitization. Typically in services, wherein the apparatus has been set, is carried out similar procedures as quickly as possible.

Note! Contacting the service does not need a subject to simple rules of operation, proper connection of the cooler, the correct installation of the bottle and on the periodic preventive sanitary requirements.

Spare parts for coolers

Often required in the heating system to replace wiring, fuse, heating element, thermostat, and in Cooling system - a fan, a cooling thermostat in the compressor cooler and cooling element. Also often need to replace the water faucet for floor or table cooler, receptacle, water inlet, connecting tubes and the power button.

Buy spare parts for coolers can be when, where equipment maintenance is performed. They can also be purchased at a specialty store. As a rule, spare parts take up little space. They are easy to transport and installation. They do not need special temperature conditions. They are available in a vast range.

It should be pointed out that buy spare parts, for example, the cup holder on the cooler, it is possible not only at the moment when the machine breaks down. It is also claimed as a preventive measure. Furthermore sanitization remove bacteria and technical mud, through which the fluid is maintained claimed supplier quality level needed periodic change parts.

Such a measure will relieve the user from major breakdowns. For example, in case of wear of the silicone sealant, silicone tube and nozzle, the lack of their fast replacement, possible breakage of the heating tank, and a compressor relay. As a result, instead of buying small details have to spend money on expensive components or even buy a new cooler.

Which can be purchased separately

Today buy parts for coolers can separate. Details can be purchased e-filling, heating system and housing. For details of e-filling and cooling concerns electronic board, button, switch, cable and wiring. Parts must be certified in accordance with GOST. The wire, having a smaller cross section, may start to overheat and melt. As a result, the fire will happen. The same applies to the other parts.

It refers to the heating element PETN, PETN elements and the hot water supply tube. Parts of this category must be resistant to temperature changes. For example, connecting tubing and valves must be made of non-meltable material quality.

To the body elements are interchangeable accessories - cranes, top covers, straps on the front panel, the front and side panels. Typically, these parts are freely available. For unique copyright model buying components is also possible.

See also:

Review of the best models of desktop water cooler

Benefits for children Water Coolers

Parts compatible with different models of coolers

To parts compatibility was one hundred percent, it is worth to purchase original spare parts. First of all, it concerns filter cassettes cooler.

In many cases, all the details of the models are interchangeable. You can always buy both the original and analogue. In many stores you can buy tap housing part, a heating tank, fan, relay, compressor butylepriemnik needle, silicone seal the top cover needle, PETN, valve, sensor, charge, switch, fuse, cup holder, a transformer, a pump for the cooler manual.

You can also buy a separation disc, a thermistor, a cooling tank, distribution tank, a screw, a locking tube, silicone tubeMagnetic fitting, disposable adapter, a water level sensor, the drain valve, fasteners, drain plug, without needle funnel and Peltier element with excellent performance and analog low-cost.

Note! Sometimes the compatibility of the plastic body parts, the cup holder to the cooler, manholes, drip pans Aqua Work or another company with coolers of other brands available. Despite possible resemblance, for example, stands for a cooler, you must advance to find out information about the compatibility of the supplier before you try to fix parts to the body.

conclusion

In the cooler water may break airbag tube holder, a check valve for a cooler, a water supply pipe, tank and other parts. The most common problem - pollution device, insufficient heating of water, the problem with liquid cooling, leakage and the presence of high noise levels.