Error 0 at Tricolor TV: which means, what to do and how to fix

click fraud protection

Scheme of satellite

CONTENT

  • 1 What does the error 0 on Tricolor TV? deciphering fault
  • 2 We find out what happened, if the error is displayed on the 0 Tricolor TV
  • 3 How to fix error on 0 Tricolor TV: effective ways

What does the error 0 on Tricolor TV? deciphering fault

It happens that in the middle of watching a movie or a favorite show on the TV screen displays a message with the error code 0. It not only afflicts the user, but requires urgent determine the cause. This fault code indicates dysfunction in the satellite equipment or software.

Repair prefix is ​​only required if none of these solutions work

Often with the question provider subscribers are turning to satellite television support, which help to cope with this problem over the phone. But, unfortunately, it is not always possible to phone service operators due to severe congestion line. In such situations, you can try to determine the cause of their own.

We find out what happened, if the error is displayed on the 0 Tricolor TV

In the case where a viewing channels on satellite operator Tricolor do not have access, you need to find influences factor: whether it is a malfunction of the service, whether the problem occurs with a particular equipment subscriber. Consider the common problem of the origin of such "trouble" in the table below.

type of problemDescription
Small hardware failureThis situation can occur due to a reconfiguration of the TV, the receiver itself or the introduction of new data for local experts. Likely to come to the aid reboot the receiver with the TV.
limit reachedThis error will appear on several TVs at the same time, since the signal of the show TV channels transmitted from one station to two receivers. In the case of debt on the subscriber's account will show the fault message, the diagnosis of this problem is by checking the operability of free channels.
Failed to update the systemSoftware failure can occur in case of change of the receiver firmware, the error is 0 appears only on a TV that is connected to this console. Remedy this situation, you can use the reinstall utility.
Improperly installed smart cardIf oxidised or module is the other side, respectively, Tricolor TV show will not. Verify the installation, you can use the keystrokes «ID» on the remote control. If the numeric value is displayed, it means that the problem of the access map.
Not activated keysThis problem can occur if the host did not look long system of television broadcasting Tricolor. Correct operation will help the continuous operation. Leave the console enabled for 8 hours. If this method does not yield results, request a re-activation of the product in the customer service.

Receiver Tricolor made on the basis of the Russian microprocessor

NOTE!(Click to see)

NOTE!

During thunderstorms it is necessary to Tricolor TV device has been disconnected from the network. It is likely that it will fail if the next lightning strike occur. In this case, you need pereproshvka equipment.

How to fix error on 0 Tricolor TV: effective ways

Register Tricolor subscriber can chat on the official website

Before the revision of the software and hardware necessary to make direct visual inspection of all the contiguous parts of the system. Be sure to check on the serviceability of all available connections: for example, if the cable from the satellite dish to your receiver, connected unreliable or completely disconnected, the supply of the display signal channel disappears, respectively, is displayed on the TV screen Error 0. We also offer you a few techniques that will help to correct the problem.

Changing the location of a satellite dish

Customize a rooftop satellite dish is not safe, you can break away and fall

It is possible that due to wind or other effects changed the direction of the satellite, so that the antenna is no longer receive electromagnetic waves that transmit TV channels. To remedy this situation is possible if the satellite dish to return to its original position. Slowly move the "plate", setting it on a new place for 3 seconds. If the signal is captured, you will hear a special sound notification. If the problem can not solve in this way, then we proceed to the following procedure.

Check the subscription period for the use of TV

Missing subscription does not require an urgent replenishment, if you do not plan in the near future to use TV

Error 0 at Tricolor TV is often arises from the absence of a subscription to a package of TV channels used. To return to full view, payments for services, and within a few hours it will be restarted. Check payment is possible by means of the service Tricolor menu, or by calling Customer Support. After login you will be available a list of channels that can be viewed, if they are not renewed, and subscription ended, refill balance of the amount specified in the operator panel.

TIP!(Click to see)

TIP!

If you can not get access to information about subscription terms, you must unplug the receiver for 15 minutes, and then turn quickly access information of interest.

Reset the software to its default settings

Reset TV settings to the "factory" does not guarantee the elimination of errors with the code 0

Any equipment with installed software must pass through the auto-update procedure. This process - not always the license, respectively, errors can occur, and then after a while on the TV, you will see a message with the error code 0 and the inability to show the prepaid package TV channels. Consider the step by step instructions to reset the receiver to the factory settings.

IllustrationDescription of the action
Press "Menu" button on the remote control or set-top box itself, so you will go with the software interface.
Next, go into the settings: This icon in the lower right corner with three gears, as in the photo.
Go to the tab "On the receiver," and press the down arrow key.
Here we see that the red lighted inscription: "Reset", press "OK" and confirm your action.
After a reset, set the options you want, starting with the time zone, of course, if it does not comply.
select the operator "Tricolor" for the central part of Russia, and other regions of the Far East, and click "Tricolor Sibir".
Choose from the list that appears "Main", click "OK", you agree to this channel search. When the process is complete label appears, be sure to save.

When all the situations reviewed, but the console does not work

Do not hesitate to contact the operator, it may have a problem with the signal transmission on your satellite dish

It happens that even the above actions do not result comes: Console does not start to work properly. Such a situation will help to correct only in the service center. To do this, call the hotline - 8-800-500-01-23, select the desired section and report the problem. You can also contact your local supplier of services provided on a specific phone. In the absence of access to telephone lines, be sure to submit your application online or on Skype.

Dear users, if you have any questions about the decision of problems in Tricolor TV with error code 0, ask them in the comments. Our editorial staff will answer you promptly.

about the author

Evgenii Tarasevich

Evgenii Tarasevich

Any technique, like a car, needs careful study and comparison before buying. Always I try to give your readers a full picture of a choice.