The outward simplicity hides aerogrill construction is rather complicated, multi-component device with a wide range of functions. However, aerogrill repair their own hands with the replacement heater is quite affordable even for users with a minimum of technical knowledge. Functionally, this improved version of the convection oven, intended for cooking by means of heated air streams.
Content
- 1 The causes of breakdowns
- 2 The appliance does not heat up
- 3 The design of the heater
- 4 dismantling of PETN
- 5 element replacement
- 6 other faults
- 7 Not rotating fan
- 8 control module
The causes of breakdowns
Despite the overall reliability and durability of the device, its main components are not immune from damage. Their appearance is often associated with banal wear during prolonged and intensive use, disregard of the requirements of the instructions, the voltage drops and other unfavorable factors.
Such problems can be a little, but the failure of PETN occurs most often and relatively easily eliminated on its own when compared to other technical problems.
The appliance does not heat up
Not always the lack of heat caused by the breakage of the aerogrill or malfunction of the heater. First of all, you need to check your device for inclusion. This is a common problem, the possible cause, which may be:
- absence of voltage on the network;
- fault outlet;
- loose contact power cable;
- wrong mode selection;
- tightly closed lid.
| Power socket | Before sin on the device, you need to check for power at the outlet. For these purposes, you can use a screwdriver indicator. In its absence, try to include another device, such as a lamp. If the suspicions are confirmed, it needs to be replaced, otherwise, troubleshooting should be continued. |
| Power cable | Next on suspicion turns out to be the connection cord. First of all, check the density of the plug contact with the socket and turn the connector in the device, then the integrity of the cable itself. If there is continuity of the cable needs to be replaced for the same. |
| Selecting | A common problem at the initial stage of use. Appliances of external signs of life, the display is functional, but when you try to go to the cooking mode, the correct response is not. In this case, you should look at the testimony of the timer. If, instead of the set time on the display zeros, the operation mode is set incorrectly. It is necessary to reprogram the device in accordance with the instructions and start again. |
| Cap | Many models aerogrill protected against accidental activation blocker or lock. If he is not brought in until it clicks, cooking mode will not be included. The solution is simple, close the lid until it stops. In a similar situation aerogrill Hotter repair may be associated with malfunctions in the lifting and lowering mechanism. |
The design of the heater
If the device turns on, tunes, but does not reach the operating temperature, the most probable cause is a malfunction of the heating element. Depending on the specific design, it may be configured as a halogen lamp or PETN various embodiments. A placement is the lower surface of the lid. Lamp or heating element mounted on special holders and contacts connected to the control board. Outwardly closed protective grille element.
dismantling of PETN
Begin repairs have to disassembly. The process is straightforward, intuitive. For its implementation will need Phillips screwdriver. After loosening the fastening screws need to:
- remove the protective grille;
- remove the retaining brackets;
- dismantle the heating element;
- free contacts.
element replacement
If you originally installed in Aerogrill gologenka, you can try to replace it with a spiral heating element. Its advantage is a greater endurance. The lamp is designed for a couple of years of trouble-free operation under standard conditions. The service life of high-quality PETN without replacing five times more. Another advantage of this version of maintainability.
If the problem is related to the spiral cliff can be restored. But it is acceptable in cases where there is no workable counterpart. Restored spiral does not last a long time, plus its repair will take a long time.
Therefore, in both cases, it is recommended to replace the defective part immediately and check renovated aerogrill for heating.
other faults
In addition to the heating element, aerogrill inoperability may be associated with other breakdowns. Not all of them can be fixed by yourself, but be aware of them will be useful. By frequently mentioned are broken fan and a failure of the control unit.
Not rotating fan
This is an important element of the device, providing uniform propekanie, frying product by blowing hot directional flow. Activated when PETN output a predetermined temperature. Failure of reduced cooking quality. The problem may be due to the breakage of soldering, which is easily recovered on its own, without leaving the house without a visit to the service center. If the node is completely unworkable, it is necessary to change on the performance:
- to this end, it is necessary to disassemble the cover completely;
- conduct a visual inspection of the contacts;
- if they are in order to perform the replacement node to a workable exact match those. parameters.
control module
The most difficult for self-troubleshooting requires the skills of working with electronics. The control module operates:
- a timer;
- thermostat;
- the launch of the device.
Externally, the control panel can be formed in the button or the more modern touch embodiment, which is more prone to failure. With such a failure, the unit will not turn on or refuses to accept the settings to the desired mode of operation.
Self Repair in this case is hardly possible, it's more that can be done - make sure the element fault, ie.. check the status of contacts and the presence of a multimeter voltage.
The board is in the body of the device fixed on the cover, to access it will have to completely dismantle the structure. Make sure it is a fault it is best to get everything back into place and contact the service center.
The best way to avoid malfunctions and extend the life of aerogrill - it's strictly follow the manufacturer's instructions. If, however, there was a failure and should not rush to puzzle over the question of how to repair their own hands aerogrill. First of all, we should correctly assess the complexity of the problem and possible to carry your instrument specialist. It will be more expensive, but will avoid the loss of time and loss of the device associated with the self-repair errors.
