Washing machine badly erases

• Wrong washing mode selected
• Problem in heating element
• Wear of drum bearings
• Stretching drive belt
• Forming mold
• Too hard water
• Economy of the

unit It's very bad when the technique begins to fail and the washing machine does not wash properly,its not to overstuff things better by hand. Any household appliance, without exception, loses its efficiency, its functionality, and sometimes it breaks down. That's the washing machine is not an exception, but rather, on the contrary - a vivid example of how an aggressive environment and dynamic loads contribute to rapid wear and damage of one of the elements of household appliances. If the washing machine badly erases, its functionality is reduced or not manifested in full, the reasons can be the following.

Bad powder

This is the very first and trivial reason. For automatic washing machines, special cleaning products are produced - powders with reduced foaming, as well as a large concentration of active components.

When choosing a detergent, pay attention to the packaging. On it there should be a special marking - the powder is intended for automatic machines. If the quality of washing has decreased significantly after you have decided to experiment with different cleaning products, we recommend changing the brand - to return to the previous one or give preference to a more reliable one. The amount of detergent per wash cycle should exactly correspond to that indicated in the instruction. On the average, 1 tbsp.l.powder is more than enough for 1 kg of laundry.

Important! Before washing, the soiled areas of the fabric should be pre-treated with simple household soap so that you do not have to use the additional functions of the equipment and thus bring the time when the washing machine badly erases.

The wrong washing mode is selected.

If things are heavily soiled, they must be washed in a special mode - at a water temperature of 90 ° C. But before you heat things up, be sure to read the label on the clothing, where the permissible temperature and mode are indicated.

If things are counter-indicative of high temperatures, then wash them in special modes such as "soaking" or "hand washing", depending on the fabric from which the product is made. If you have problems with stains on clothes, set a special "stain removal" mode or add components intended for this purpose to the detergent.

Important! For strong stains or stains, apply a dish detergent and place the item in the drum. You can select any mode for washing.

Problem in the heating element of the

The most common failure in which a washing machine badly erases things - the burning of the main working element - the heating element. A characteristic sign of this failure is that there is no heating of the water in the tank.

The heating element can fail for two reasons:

• overvoltage in the mains;
• increased scale build-up.

Important! In the event of a failure of the heating element, the washing process at high temperatures can not pass, and therefore, the white linen acquires a worn appearance, becomes dirty gray. If the problem is in the TEN, then call the master who will find out the exact cause of the failure and correct it.

Drum Bearing Wear

If the machine is not new, bearing wear is possible. As a result, the drum starts to spin much less and less often, and this, in turn, affects the quality of washing. To check if this is a malfunction in your machine, start the standard cycle, note whether the drum rotates at a sufficient speed. This failure you can determine even visually. To fix the situation, you need to replace the bearings, because they provide the rotation of the drum.

Important! If the bearings are not replaced in time, they will start to be corroded, and the grease applied to them will leak into the tank during washing and spoil things.

Stretch the drive belt

If the drum does not spin or spin too slightly during washing, the drive belt may have sprained. Qualitative washing, in this case, should not be expected. To solve the problem of washing the washing machine badly - replace the belt.

Formed mold

Sometimes, mold can be left on the washed goods, formed on the walls of the drum or on the sealing cuff of the hatch. To prevent mold from appearing in the washing machine, periodically start the washing process in boiling mode. At the end of each cycle, leave the hatch door open for several hours until the drum dries completely.

If the mold has already formed, then perform antiseptic measures or replace the manhole cuff with a new one( if necessary).

Too hard water

If you use too hard water during washing, the detergents will not foam well, and things will not clean properly. Therefore, determine the hardness of the water( consult the relevant organizations), and if necessary, add special softeners or replace the dry detergent with a liquid detergent. Many housewives noticed that as a result of such a simple action, the laundry becomes much cleaner, and even softer.

Important! Add to the powder 1-2 tbsp.l.soda ash for 1 wash. This will not only soften the water, but also improve the quality of washing. Bleached washed white things can also be done with the usual household soap: grind it and add it in a small amount to the powder compartment.

Economy of the

Some budget models of washing machines use water so economically that the quality suffers during the washing process. Usually this concerns the rinsing process, when due to the reduced volume of water on the products there are white divorces from soap products. To fix the situation, try to reduce the amount of laundry when loading.

The exact reason for washing the washing machine badly can only be diagnosed by a qualified technician. And you are advised to strictly follow the operating instructions for the unit, follow the rules and tips for caring for the washing machine to extend the life of household appliances, respectively - to improve the quality of washing.