Circular saw is used to saw wood.
Using a handsaw is not always comfortable, the use of the table allows you to make cutting process more smooth and precise
Cutting the substrate has a plane resembling disc equipped with an outer edge with teeth. There are models not only manual type, but can be fixed on the table.
Working with large volumes of wood conventional circular saw is difficult, so it is best to set the table
There are several ways to get the last one for the convenience of manipulations. Table circular saw can build your own, exactly adhering to a certain scheme.
table device for circular saws
Content
- 1 Benefits of creating their own hands
- 2 We determine the design and construction
- 3 Blueprints
- 4 Necessary materials
- 5 Required tools
- 6 The manufacturing process: step instruction
- 7 Video: Table conveyers from scrap materials
Benefits of creating their own hands
The table is made in view of the fact that the hand tool is installed and fastened on the table, turning at the same time in stationary equipment
The construction element allows you to make your own hands saw the most suited to the individual conditions. Difficulties in the process will not occur, if carefully examined. You can adjust the product to size, distribute it so that it was convenient for you.
Make a table circular saw quite capable of every master
Personally created model is the only one of its kind that makes it unique.
A small desktop stand for conveyers
We determine the design and construction
The easiest one for the table structure of the conveyers is sufficiently thick plywood and boards
The base may be made of wood or metal. For countertops selected leafy tree species. It should make a special hole for the drive. A key feature of the table is to be created convenience.
The bed circular machine
It should take care of its stability. No slacking is unacceptable, otherwise it will have a negative impact on safety. We countertops should get the most even surface. Then it decreases the risk of injury at work.
Table circular saws require compulsory attendance guides
The construction may be supplemented by a special riving knife. It can be removed. Its equipped with special disk protection allowing to get rid of the working chip flying.
The guide table carriage for conveyers
Some removed the plant cover and changing the factory to a makeshift platform. If you do not intend to carry out the cut at an angle, it is possible to remove the parts that regulate the inclination of the disc.
Blueprints
The circuit for producing the table for the circular saw
Before you begin, it is recommended to pass a preparatory stage. Be sure to make the drawing. This will facilitate the process of creating a design. First, calculate the size of the table, then transfer the data to the paper. Hole performed in the construction must exactly fit to the size of the saw. It all depends on the brand of equipment. Because you can not make a universal hole. The base must be sustainable and well withstand mechanical nature.
Drawing table for conveyers with their hands
Repositioning impermissible construction of one of the parties. Dimensions of table top should fit the cutting stream. The final version is detected based on the individual desires. Some are comfortable with a folding table or a product with small dimensions.
Drawing universal desktop machine
In the drawings should be considered an important point. If the plans at the left on the table tools or materials, then the dimensions of countertops should be increased to one square meter in area. A suitable size is 120 to 120 cm. It should be done carefully and slowly drawing to do everything correctly.
section diagram for describing an exploded conveyers with
Necessary materials
Homemade table can be made from wood
Wood can be used for this table, plywood or chipboard. Also suitable MDF and particleboard. Some preferred to select steel or aluminum.
Table circular machine steel plate
It is not recommended to use plastic, it is totally unsuitable for the purpose of this table. If the selected timber, then after completion of the assembly should be treated with special antiseptic product composition. It provides reliable protection against moisture and help prevent decay.
To make the table saw their own need to prepare the materials.
- The selected raw materials for the basics. The thickness should be 21 mm.
- Timber required for the frame. Suitable edged board 3 meter with dimensions 50 by 150 mm. All you need 5 pieces.
- Dowels of wood with dimensions of 10 cm. Not less than 12 pieces.
- Joiner's glue.
- Metal fastening in an amount of 4 pieces.
- Corners of metal. Only 10 pcs.
- Self-tapping screws.
These elements need to prepare in advance and arrange around the workplace.
Required tools
In addition to the materials should be prepared tools.
Among them:
- Pens and markers;
- instruments for measuring, including the meter and roulette;
- jigsaws;
- manual frezer;
- machine for grinding;
- nazhdachka (or should have a fine average grain size);
- planer and drill;
- screwdriver.
Prepare everything in advance and need to keep on hand throughout the entire process.
The manufacturing process: step instruction
Marking places saw attachment to the table
Marking and fixing ribs
Countertops under a circular saw in finished form
To make high-quality construction is necessary to follow some tips. The process consists of several steps, presented in the table.
| Steps | Description |
| 1 | The bar on all sides should trim using planer. Then out of it is going to frame the future table. In each of the parties countertops need to drill some holes for 5 mm. Additionally, one through-runs for the product feet. |
| 2 | In tsargami performed on several holes of the same diameter. The legs of one through-operate. Diameter remains the same, 5 mm. |
| 3 | Proceed to install the dowels into the countertop. Prior to this, they are covered by the carpenter's glue. Legs placed on top and side-bar. If there are ties, clamps with the product must be secured with the help of them. When the glue is completely dry you need to seal the side-bar and legs using special fasteners of metal. Further, it should pull the screws. Add construction reliability and durability can be, using the corners. They will become part of the additional attachment, will give the product stability. For sufficiently short side pieces 2 and 3 are suitable for long. |
| 4 | The next step involves securing the saw on the inside of the product. There are several methods to carry out the task. To secure fit bolts or bars with M4 screws. The first case is fast and reliable. The second method does not involve additional holes, which eliminates the need to drill. Need to do drink in the bars, the width of which is equal to the dimensions of the site saw. Further, screws and bars on both sides of the table top and fasten equipment |
| 5 | After installing the saw will need even larger bar. It using screws, fixed on the basis of design. Screwing is performed at elevations made at exhibiting platform in the flat position. These manipulations can help, taking the saw, it is usually returned quickly without searching for layouts |
| 6 | the saw blade is mounted on the allotted space. The basis for longitudinal saw through the hole. Then the product should be turned |
| 7 | Then begin to manufacture the rip fence. By sawing off two strips of plywood. Their length must be equal to the width of the table. On average, these dimensions are 10 cm. The angles should be rounded |
| 8 | The resulting polished strip. They need to bond angle screws. Inside should be corner fasten metal |
| 9 | If you want to fix the focus and on the basis of the structure will be used frequently, you should attach the guide so that it was perpendicular to the disk. Pin roller at the bottom. This will allow him to move. |
Attaching the legs to the table
Mounting the saw to the table top
Fixing the start button
The structure is made and ready to use. In carrying out the described manipulation is important to remember to stay safe. It applies to any manipulation of the circular saw.
Regularly check the position of the table, and his castle. The construction must be stable, without loosening.
EXAMPLE manufactured desktop for circular saws
table option for hand-held circular saw with a lifting mechanism
First, make sure the saw safely secured, only then to turn on it. You can not keep cutting the material by hand. This will help prevent the wood hit in the face when they start bouncing knots. Additionally recommended for the use of special goggles.
For safety, always use protective eyewear
These simple tips will help avoid accidents in the workplace.
