F4 error on the washing machine Atlant: what to do and how to fix

• damage to electronic locking the lock;
• violation contacts or wiring between the control unit and the lock;
• the machine is in violation;
• skewed hinges;
• defect or plastic retainer guide.

To repair a blocking lock, contacts and the wiring between the control unit and lock:

1. Check the lock operation.
2. Rang multimeter its wiring.
3. Faulty components replaced.
4. Set the level of the car.
5. If necessary, tighten the loop and replace the broken handle.

Sel: Damage to the interface module

The reasons for the fact that no one indicator light is not lit:

• breakdown of program selection selector;
• retraction or sticky keys.

To eliminate test the keys and selector. Test and replace the electronic board failure.

None: drum overflow foam

If all four lights are lit:

• wrong choice of type and amount of SMS;
• choosing the wrong program for washing.

To eliminate, change the type of SMS and adjust the amount of detergent. Select the appropriate wash program.

F2: Defective temperature sensor

The reasons that illuminates diode № 3:

• crash sensor, controlling the water temperature;
• interruption of communication control module and a thermistor;
• a defect in the control unit.

To fix:

1. Replace with a new sensor.
2. Rang, replace the wiring and contacts as necessary.
3. Test the control module.

F3: Defective Heater

Shine № 3 and 34. In the washing machine Atlant f3 error occurs for the following reasons:

• short circuit that caused the broken wires;
• damage TEN-a;
• damage to the temperature sensor;
• accumulation of scum on TEN's.

To eliminate rang heater, his contacts and thermistor. Descale and replace faulty parts.

F4: Problems with drainage water

The sensor number 2 on the following reasons:

• clogged drain waste system components, coins, small items of laundry;
• kinked hose;
• I broke down the drain pump.

To fix the washing machine Atlas error f4:

1. Check the condition of the drain unit, remove blockages and excesses.
2. Check and clean the filter.
3. Inspect the condition of the pump and replace it with a new one in the case of apparent damage.

F5: Problems with a set of water

№ signals 2 and 4. Error f5 in a washing machine Atlanta is displayed in the following cases:

• insufficient pressure in the pipes;
• clogged drain node rubbish clogging;
• breakage of the inlet valve.

To fix:

1. Check the water pressure and the free access to it.
2. Remove the blockage of the inlet hose and filter on the grid behind it.
3. Clean the valve hoses.
4. Check the voltage on the valve spools. Broken item replaced.

F6: It does not work reverse relay

Indicators № 2 and 3 are lit because:

• defective contacts or relays;
• reason in the motor.

Inspect all components for repair and replacement of defective.

F7: Incorrect mains

№ indicator LEDs 2, 3 and 4:

• network performance is not as declared for SMA;
• the problem of interference filter or control module.

Before working with the mains switch off the machine.

Replace the filter or control module. Evaluate network performance tester and modify as needed.

F8: In stiralki tank too much water

LED lights № 1:

• incorrect operation of the pressure switch or electrical circuit;
• malfunctioning control module;
• exhaust valve stuck in the open position.

To fix:

1. Inspect the pressure switch.
2. Blow its tube.
3. Replace defective pressure switch and control module.
4. Jammed valve, remove and replace with a new one.

F9: tachosensor not functioning

№ lit bulb 1 and 4. Error f9 in the washing machine Atlant occurs for the following reasons:

• broken tachogenerator or the engine;
• damaged wiring or contacts.

For elimination:

1. Diagnose the details.
2. Replace any damaged parts.
3. Rang contacts and wiring, replace if damaged.

F10: Electronic door lock does not work

LEDs 1-3 lit number, if there is no signal of the deadlocks. Machine "Atlas" does not start.

To eliminate start pinging UBL and contacts. If necessary, install a new UBL.

F12: Broken engine

Signals № diodes 1, 2, 3:

• engine failure;
• interruption or breach winding contacts;
• semistors burned on the board.

Replace the motor and winding in case of a defect. Inspect and replace the control board.

F13: Damage to the circuits, the contacts, the control board

Diodes № 1 and 2 indicate an error in the following cases:

• water penetration;
• short circuit.

Rang and inspect parts. Replace the areas with identified lesions.

F14: software error

Diodes № 1 and 2. It is the result of a software failure.

Try resetting the failure disconnection and reconnection of the machine. 100% effective reinsertion or replacement module.

F15: The leakage system

Possible reasons:

• wear or tear a rubber cuff;
• depressurization of the hose, the drain node;
• violation of the integrity of the tank.

For elimination:

1. Check the integrity of the cuff and the tank.
2. Replace them when a fault is detected.
3. Check all drain components for leaks.
4. Defective hoses and nozzles, replace with new ones.

To simplify the problem diagnosis and repair of household appliances, manufacturers have designated codes common breakage. Meaning washing "Atlant" machine error codes pinpoints the problem. Despite the ease of repair, sometimes need expert help.